Home About us products feedback Contact us
 
   Home | Products |1|2| 3|4| 5| 6| 7| 8| 9| 10| 11| 12| 13| 14| 15| 16| 17| 18| 19| 20 Price List | 21                                                                                                                                                                                                           
INSTRUCTION FOR USE

It is easier to use the cutter if permanently attached to table or a punch using the fixture point provide. The depth feed always be mm hards and soft material 2.5 mm thick and over should be cut from both sides.

  • Cut center hole 16 mm (5/8”) diameter with punch provide.
  • Place cutting base on center
  • place gasket material on centring pin and using steel measuring tape adjust pin position to require radius first cut O.D. of gasket and sheet Cut I.D. of gasket
  • Cheak diameter and correct if necessary.
  • Feed cutting wheel lightly into material and make full turn with chock mark.
  • Proceded to cutting using slight pressure cutter hard wheels.
  • Desing and diamension subject to alteration.
  • Ring of over 3 mm thickness are best cut out with a cutting base first cut the material spare extra cutting wheel on special request at extra cost.
  • A necessity for your tool box in maintenance shop & power plant out gasket patterns shape from plainable material cut Non Asbestos.Celophone cork corrugated board filter linoleum Plastic Rubber valcanised Fiber / Teflon. Aluminium / Copper / Stainless Steel soft foil can be cut smooth.
  • MK III is most economical in rate & time saver smooth cut for each gasket if you can cut by chisel it take for each gasket more times & not getting correct edge cut of ring as it manually cut & also proper seal will be not done. Because of gasket are not in smooth cut, mfg . die is cost Rs. 1250/- for each and it will cut only single dimention Diameter of gasket ring while here you can 2” to 5 ft. dia within a couple of minutes. Time of making die 15 to 20 days while our MK III Cut on the sports range 2” to 5 ft. dia 6 mm thick compressed non asbestos wire rainforced joining sheets are available (5 ft x 5 ft ) even uneven shape to be cut with free accessories we provide lit covers full range of gasket to cut 5 ft. dia maximum thickness 6 mm this prove that MK-III is most economically rate & easy to carry one place to another in remote areas as MK-III with only 20 kg.
FROM THE MANUFATURERS OF WORLD FAMOUS

2)
NEW WILCOX MAKE GASKET CUTTER BOLT HOLE ALSO MM & INCHES BOTH ARE PRESCRIBED OF ON EVERY PUNCH.
  •  ARCH PUNCH SET MODDEL 1100 INR. 30,000/- PER EACH SET RANGE- 1/8” TO 7/8” DIA.
  •  ARCH PUNCH SET MODULE 2200 INR. 35,000/- PER EACH SET RANGE 1” TO 1.7/ 8” DIA. MM & INCHES  BOTH ARE GIVEN

Model No. 1100 M.M & inches both are given. As illustrated consist of Arch Handle ring and 13 cutter size 1/8” 3/16” 1/4” 5/16” 7/16” 1/2” 9/16” 5/8” 1-1/16” 3/4” 1-3/16” and 7/8” inclusive carring as made from soft wood for maximum tools protection.

 

 

Model No. 2200 M.M & inches both are given. Consist of Arch Handle Retaining Ring and 9

cutter size 1” 1.3/16” 1.1/14” 1.5/16” 1.3/ 8” 1.1/2” 1.5/ 8” 1.7/ 8” Soft for maximum protection.

 




You will be AMAZE of the DURABILITY of the CUTTER EDGES inches and mm both gives make on cutter Model 1100/2200 inter chargeable cutter are special high alloy steel, both treated. Band hardened to extra standard and ground to precision tolerance for large life Zing planted cutter are uniformly straight for their enter length assuring erection of the material though the cutter no more clogging for economy, cutter design enable. This tool cut hold from anything pliable in seconds.

  Wilcox Make C.S. Safety Valve 80mm Cast Carbon Steel Angle Type Safety Valve for Gas / Oil

Wilcox Make C.S. Safety Valve 80mm Cast Carbon Steel Angle Type Safety Valve having Biody/Bonnet castings confirming to ASTM A 216 GR. WCB, Bolted, Aisi 410 internals, Spring of Spring Steel, Planged ends. Set press are - Inlet Flange : Fitted with Nozzie & Drilled as per your Dimensions Work Pressure required for Oil, Gas & Steam. Outlet Flange : Drills to ASA 150# Size : 80mm

 

      © Copyright 2013  Wilcox Boiler (c) Industries  All rights reserved. e logo